Safety Recall NHTSA · 22E067000 Reported August 15, 2022

Stabilizer beam welds may crack over time

Q: What is recall 22E067000?

NHTSA recall 22E067000 was issued by Iowa Mold Tooling Co., Inc. on August 15, 2022. It addresses: Stabilizer beam welds may crack over time. The recall affects approximately 31 vehicles , with the defect involving the N/A component.

Q: Is my vehicle included in this recall?

The only way to confirm is to look up your 17-character VIN at nhtsa.gov/recalls . NHTSA's tool will tell you if VIN-by-VIN this exact recall applies.

Q: How long do I have to get a recall repair done?

There is no expiration on most federal safety recalls. Even if your vehicle is years old and you bought it used, the manufacturer is required to perform the repair at no cost.

Iowa Mold Tooling Co., Inc. · N/A · 31 vehicles potentially affected

NHTSA ID

22E067000

Manufacturer Campaign

TB2022001 - IMT dist

Manufacturer

Iowa Mold Tooling Co., Inc.

Component

N/A

Vehicles Affected

Recall Type

Equipment

Report Received

August 15, 2022

Completion Rate

100.00

Defect Summary

Iowa mold tooling co., inc. (imt) is recalling certain hydraulic loaders, model 42684 and part number 6390121. the welds on the stabilizer beams may crack over time, or break under load.

Safety Consequence

A cracked or broken stabilizer beam can cause the vehicle to tip, or disengage the load, increasing the risk of injury.

Corrective Action

Dealers will replace the stabilizer beams, free of charge. vehicle manufacturers were notified september 23, 2022. owners may contact imt customer service at 1-877-751-4222. imt's number for this recall is tb2022001-imy dist.

What you should do

Look up your VIN at nhtsa.gov/recalls to confirm this recall applies to your vehicle.
Contact an authorized Iowa Mold Tooling Co., Inc. dealer and reference recall ID 22E067000 or campaign TB2022001 - IMT dist.
Schedule the free repair. By federal law, the manufacturer must remedy the defect at no cost.

View Official NHTSA Notice →

Similar Recalls

Other recalls from Iowa Mold Tooling Co., Inc. or involving N/A.

Recall 26V290000

Chrysler (fca Us, Llc)

Power transfer unit may fail and cause a loss of drive power

N/A · 61,711 affected · May 7, 2026

Recall 73V092000

Harley-davidson Motor Company

Brakes:mechanical service:other

N/A · 2,607 affected · Apr 30, 1973

Recall 73V094000

Harley-davidson Motor Company

Suspension

N/A · 11,705 affected · Apr 30, 1973

Recall 26T011000

Goodyear Tire & Rubber Company

Tire tread may separate

N/A · 69 affected · Apr 18, 2026

Recall 26E021000

Chrysler (fca Us, Llc)

Engine failure may cause fire or loss of drive power

N/A · 2,689 affected · Apr 16, 2026

FAQ: Recall 22E067000

Your rights, the repair process, and what each field on this page means.

What is recall 22E067000?

NHTSA recall 22E067000 was issued by Iowa Mold Tooling Co., Inc. on August 15, 2022. It addresses: Stabilizer beam welds may crack over time. The recall affects approximately 31 vehicles, with the defect involving the N/A component.

How do I get this recall repaired?

Contact any authorized Iowa Mold Tooling Co., Inc. dealer and reference NHTSA recall ID 22E067000 or the manufacturer campaign number TB2022001 - IMT dist. Under federal law, the repair is completely free regardless of vehicle age or owner history.

Is my vehicle included in this recall?

The only way to confirm is to look up your 17-character VIN at nhtsa.gov/recalls. NHTSA's tool will tell you if VIN-by-VIN this exact recall applies.

How long do I have to get a recall repair done?

There is no expiration on most federal safety recalls. Even if your vehicle is years old and you bought it used, the manufacturer is required to perform the repair at no cost.

Where does the data on this page come from?

All information on this page is sourced directly from the U.S. Department of Transportation public dataset for NHTSA recalls. Last refreshed: 2026-05-22. For the most current official notice, visit nhtsa.gov/recalls.